Go to Trans Tech Home Page
Go to What's New Go to Support Go to Machines Go to Supplies page Go to Special Services Go to Contact Us page
PAD PRINTING INK:
Type PM Ink

• Single-Component
• Glossy Finish
• Semi-Opaque,
• Fast-Drying

Type PM Ink is a glossy, single-component, semi-opaque, fast drying ink. It provides good adherence to untreated plastics which commonly require pre-treatment prior to printing. Testing is essential for each application. When fully cured, it provides outstanding resistance to:
• Chemicals
• Organic Solvents
• UV Light

For more details, see Ink Data Charts below.

Ink Data Charts:

• Ink-to-Substrate Compatibility Chart

• Ink Characteristics Chart

• Color Availability Chart

• Ink Drying & Curing Times Chart

• Ink Additives Chart
Ink Types:

B - B/GL - C - E - G

HS - J - NK - O - P - PC

PD - PG - PH - PK - PL

PM - PV - R - SUB - U

UVA - UVE - UVHC - W
Any questions?
Ask your consumables representative at:
630.752.4000 or e-mail us

For ink troubleshooting questions, click here!

Since operating conditions and applications are beyond our control, ITW Trans Tech cannot guarantee results nor assume liability for any problem that may arise. The user should test the suitability of the product for its intended application. No warranty for results obtained, expressed or implied, can be assumed by ITW Trans Tech.


Order from our Online Store!


INSTRUCTIONS:

NOTE: Read Material Safety Data Sheet (MSDS) Prior To Use

Ink Type PM is a single-component product supplied in paste form. Thinner ( if needed ) should be thoroughly mixed with the ink prior to using. During printing, the ink viscosity may be adjusted with thinner (if needed). A retarder may be added to slow drying rate during printing (normally for high room temperatures or multi-color use). Recommended room temperature: 70-78 degrees F. Recommended room humidity 30-50 %

ADDITIVES: (See Additives Chart for more listings)

Thinners:
THINNER B (5 to 20 % by weight) Faster
VD THINNER (5 To 20 % by weight) Medium
THINNER BGA (5 To 20 % by weight) Slower

Retarder:
TPD RETARDER (1 To 3 % by weight)

DRYING & CURING: (See Ink Drying & Curing Times Chart )
Ink TYPE PM dries to the touch within 15 – 30 seconds at room temperature. Drying time may be reduced with forced hot air at 200 – 400 degrees F. Normally, full cure is achieved after one to two days depending on curing temperature time; and humidity. Heat curing is necessary for better adhesion and performance results.

COLORS: (See Color Availability Chart )
Ink Type PB is available in:
• Process colors
• C-Mix 2000 Color Matching System
• Custom Colors Available Upon Request

NT (non-toxic) Inks
Our NT Series Inks conform to US C.O.N.E.G. Legislation and European Standard EN 71, part 3 Safety of Toys (1989). For special applications (examples: Medical, Automotive, MIL-STD) please contact us.

USE & STORAGE INFORMATION
(For more detailed information see Material Safety Data Sheet (MSDS) for Type PM Ink.

Ink Type PM:
Stir ink thoroughly before removing from container. Reseal lid tightly after using.
Shelf Life: One year (in original sealed container)

THINNER: Reseal lid tightly after using. Shelf Life: two years (in original sealed container)

RETARDER: Reseal lid tightly after using. Shelf Life: two years (in original sealed container)

STORAGE OF ALL PRODUCTS: At room temperature 60 to 80 Degrees F with low humidity.


Ink Type PM: Recommended Printing Substrates

# : Indicates substrate may require pretreatment.

Substrate:
Name / Chemical Name		 ASTM / ISO
Abbreviation		 Plastics Family Trade Name
THERMOPLASTICS . . .
Polypropylene # PP Polyolefin .
. . . .


Home | Consumables | Machines | Support | What's New | Specialty | Trade Shows | Contact Us

© 2006 ITW Tans Tech • An Illinois Tool Works Company