 |
||||||||
 |
 |
 |
 |
 |
 |
|||
|
|||||||||||||||||||||||||||||||||||
|
INSTRUCTIONS: NOTE: Read Material Safety Data Sheet (MSDS) Prior To Use Ink Type PK is a one or two-component product supplied in paste form. Hardener must be added for production use. Ink and hardener should be thoroughly mixed prior to adding thinner. During printing, the ink viscosity may be adjusted with thinner (if needed). A retarder may be added to slow drying rate during printing (normally for high room temperatures or multi-color use). Under most conditions, ink pot life will not exceed eight hours. Recommended room temperature: 70-78 degrees F. Recommended room humidity 30-50 % SPECIAL INFORMATION: • Transfer pad life may be shorter with type PK ink. • If using an ink pump system, ink replacement once per week is recommended. This is necessary because the ink sometimes hardens into little balls, and settles to the bottom of the pump. SPECIAL ADDITIVES: • For cliché oxidization / rusting problems use Anti-Corrosive Ink Thinners VD/00 OR B/01. • For a Write-On Capable ink (single component), use Fuller 33 Additive. ADDITIVES: (See Additives Chart for more listings) Hardeners: (mixing ratio, ink to hardener) • BH HARDENER (10 : 1 Ratio by weight) For most applications. • BH/N HARDENER (10 : 1 Ratio by weight) More ultraviolet light and abrasion resistant but requires additional drying time. Thinners: THINNER B (1 to 15 % by weight) Faster THINNER B/01 (1 To 15 % by weight) Faster (anti-corrosive thinner) VD THINNER (1 To 15 % by weight) Medium VD/00 THINNER (1 To 15 % by weight) Medium (anti-corrosive thinner) THINNER BGA (1 To 15 % by weight) Slower Retarder: TPD RETARDER (1 To 3 % by weight) Other: FULLER 33 6 % by weight For Write-On Capable Ink DRYING & CURING: (See Ink Drying & Curing Times Chart ) Ink TYPE PK dries to the touch within 15 – 30 seconds at room temperature. Drying time may be reduced with forced hot air at 200 – 400 degrees F. Normally, full cure is achieved after one to two days depending on curing temperature time; and humidity. Heat curing is necessary for better adhesion and performance results. COLORS: (See Color Availability Chart ) Ink Type PK is available in: • 23 Standard Opaque Colors • Process Colors • Custom Colors Available Upon Request • C-Mix 2000 Color Matching System NT (non-toxic) Inks Our NT Series Inks conform to US C.O.N.E.G. Legislation and European Standard EN 71, part 3 Safety of Toys (1989) For special applications - examples, Medical. Automotive; MIL-STD please contact us. USE & STORAGE INFORMATION (For more detailed information see Material Safety Data Sheet (MSDS) for Type PK Ink. Ink Type PK: Stir ink thoroughly before removing from container. Reseal lid tightly after using. Shelf Life: One year (in original sealed container) HARDENER: Reseal container immediately after using. Hardener is humidity sensitive. As moisture is absorbed, the viscosity first increases, then starts forming crystals. Do not use when crystals first appear. Shelf Life: one year (in original sealed container) THINNER: Reseal lid tightly after using. Shelf Life: two years (in original sealed container) RETARDER: Reseal lid tightly after using. Shelf Life: two years (in original sealed container) STORAGE OF ALL PRODUCTS: At room temperature 60 to 80 Degrees F with low humidity. Ink Type PK: Recommended Printing Substrates # : Indicates substrate may require pretreatment.
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Home | Consumables | Machines | Support | What's New | Specialty | Trade Shows | Contact Us © 2006 ITW Trans Tech • An Illinois Tool Works Company |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
